SUMMARY #2: sol9 + 3510FC + qlogic qla2340-CK

From: Adam Mazza <adam_at_68e.com>
Date: Tue Jun 22 2004 - 11:15:21 EDT
You can also grab the fcode from Qlogic and flash the card, once the
driver is loaded.

Adam

> Solution:
>
> I gave Qlogic a call, and they informed me that the fcode on the card was
> for an x86 box, which is why I wasn't seeing the card with probe-scsi-all
> apparently, or from cfgadm. To get the disks to be recognized correctly I
> edited sd.conf to include the below target (40) and all is fine now. While
> I would prefer a card with Sun fcode, this isn't a production system, and
> this solution works fine.
>
> Regards,
>
> Adam Mazza
>
> Original Message:
>
> > Hello,
> >
> > I have a v240 running Solaris 9 04/04 directly attatched to FC0 of a
> > 3510FC. The problem is the OS does not seem to be recognizing the array.
> > The configuration is as follows:
> >
> > 1) Qlogic qla2340-CK card. I installed the most recent driver and dmesg
> > shows the following upon bootup:
> >
> > QLogic qla2300 Fibre Channel Driver v4.13 Instance: 0 Firmware v3.2
> >
> > then brings the loop up, shows the adapter node-name, port-name, and
> > adapter-port-id then the SCSI-target-id with fibre-channel-node-name. Then
> > is shows the 2 luns I have enabled off the array:
> >
> > kern.info] qla2300-hba0-SCSI-target-id-40-lun-0-enable;
> > kern.info] qla2300-hba0-SCSI-target-id-40-lun-1-enable;
> >
> > and finally:
> >
> > kern.info] PCI-device: fibre-channel@1, qla23000
> > kern.info] qla23000 is /pci@1d,700000/fibre-channel@1
> >
> > So the card seems to recognize the array correctly.
> >
> > 2) 3510FC array. I've upgraded the FW, SES, and PLD on this:
> >
> > sho inquiry
> >  Vendor: SUN
> >  Product: StorEdge 3510
> >  Revision: 327R
> >  NVRAM Defaults: 327R 3510 v2.63
> >  Bootrecord Version: 1.31H
> >  Serial Number: 07D30F
> >
> > sho ses
> > Ch  Id Chassis Vendor/Product ID    Rev  PLD  WWNN             WWPN
> > -------------------------------------------------------------------------------
> >  2  12 07D30F  SUN StorEdge 3510F A 1040 1000 204000C0FF07D30F
> > 214000C0FF07D30F
> >                                                      Topology: loop(a)
> >  3  12 07D30F  SUN StorEdge 3510F D 1040 1000 204000C0FF07D30F
> > 224000C0FF07D30F
> >                                                      Topology: loop(b)
> >
> > and the array is in loop only mode.
> >
> > 3) SFS - I downloaded SAN_4.4a_install_it from Sun along with the
> > 3510array.sh script and they both ran fine.
> >
> > Unfortunately luxadm probe, or the sccli command does not see the array
> > (except via oob management).
> >
> > I was wondering if anyone else is using this particular FC card with this
> > array. I've been told it should work, but since it's not a Sun branded
> > card it's not listed on Sun's site as supported.
> >
> >
> > Thanks
> >
> > Adam Mazza
> > _______________________________________________
> > sunmanagers mailing list
> > sunmanagers@sunmanagers.org
> > http://www.sunmanagers.org/mailman/listinfo/sunmanagers
> >
> >
>
> Adam Mazza
> PGP Key:http://pgp.mit.edu:11371/pks/lookup?op=get&search=0x382775D1
> Key fingerprint = 5A82 FA7F 459C E805 6C00  3211 48AC 6069 3827 75D1
> _______________________________________________
> sunmanagers mailing list
> sunmanagers@sunmanagers.org
> http://www.sunmanagers.org/mailman/listinfo/sunmanagers
>
>

Adam Mazza
PGP Key:http://pgp.mit.edu:11371/pks/lookup?op=get&search=0x382775D1
Key fingerprint = 5A82 FA7F 459C E805 6C00  3211 48AC 6069 3827 75D1
_______________________________________________
sunmanagers mailing list
sunmanagers@sunmanagers.org
http://www.sunmanagers.org/mailman/listinfo/sunmanagers
Received on Tue Jun 22 11:15:16 2004

This archive was generated by hypermail 2.1.8 : Thu Mar 03 2016 - 06:43:34 EST