Summary: jumpstart for netra X1

I have many people that responded (most saying essentially the same thing
the instructions said), however Rob Lyle [rob@consus.co.uk] had the
solution. Seems the netra X1 cannot boot from a Solaris (Intel) boot server.
I went through the same procedure on an E450 and everything functioned
properly.

Thanks.

James Richardson
Senior Unix Administrator
Horry Telephone
(843) 369-8549


> -----Original Message-----
> From: Richardson, James 
> Sent: Monday, July 30, 2001 14:52
> To: sunmanagers@sunmanagers.org
> Subject: jumpstart for netra X1
> 
> 
> Greetings,
> 
> I have searched the archives but could not find an applicable 
> solution.
> 
> I am trying to configure a jumpstart server for our netraX1 
> servers. I have followed the directions in the advance 
> installation guide and the release notes all with out 
> success. I have setup jumpstart servers for 420R,440R, E450 
> and Ultra 10 but can't seem to get this guy to work. He seems 
> to have problems loading the ethernet driver.
> 
> Here is a screen dump.
> 
> ok boot net
> Res
> LOM event: +1h48m52s host reset
> etting ... 
> 
> 
> Processor Speed = 400 MHz
> Baud rate is 9600
> 8 Data bits, 1 stop bits, no parity (configured from lom)
> 
> Firmware CORE  Sun Microsystems, Inc.
> @(#) core 1.0.1 2001/02/19 09:55
> Software Power ON
> Verifying NVRAM...Done
> Bootmode is 0
> MCR0 = 16a0b004
> MCR1 = c0804000
> MCR2 = f80a000
> MCR3 = 202
> Ecache Size = 256 KB
> Clearing E$ Tags Done
> Clearing I/D TLBs Done
> Probing memory
> Done
> MEMBASE=0x60000000
> MEMSIZE=0x8000000
> Clearing memory...Done
> Turing ON MMUs Done
> Copy ROM to RAM (148440 bytes) Done
> Orig PC=0x1fff0007efc  New PC=0xf0f07f54
> Processor Speed=400MHz
> Looking for Dropin FVM ... found
> Decompressing Client Done
> Transferring control to Client...
> Reset Control: BXIR:0 BPOR:0 SXIR:0 SPOR:1 POR:0 
> Probing upa at 1f,0 pci 
> Probing upa at 0,0 SUNW,UltraSPARC-IIe (256 Kb)
> Loading Support Packages: kbd-translator 
> Loading onboard drivers: 
> Probing /pci@1f,0 Device 7  isa dma rtc power SUNW,lomh serial serial 
>    flashprom 
> Probing /pci@1f,0 Device 3  pmu i2c temperature dimm i2c-nvram idprom 
>    motherboard-fru ppm beep fan-control 
> lomp 
> Probing Memory Bank #0   0 Megabytes
> Probing Memory Bank #1   0 Megabytes
> Probing Memory Bank #2   0 Megabytes
> Probing Memory Bank #3 128 Megabytes
> Probing /pci@1f,0 Device 7  
> Probing /pci@1f,0 Device 3  
> Probing /pci@1f,0 Device c  ethernet 
> Probing /pci@1f,0 Device 5  ethernet 
> Probing /pci@1f,0 Device a  usb 
> Probing /pci@1f,0 Device d  ide disk cdrom 
> Sun Netra X1 (UltraSPARC-IIe 400MHz), No Keyboard
> OpenBoot 4.0, 128 MB memory installed, Serial #50735678.
> Ethernet address 0:3:ba:6:2a:3e, Host ID: 83062a3e.
> 
> 
> 
> Environment monitoring: disabled
> Executing last command: boot net                                      
> Boot device: /pci@1f,0/ethernet@c  File and args: 
> Using Onboard Transceiver - Link Up. 
> 2aa00 
> Server IP address: 172.16.1.124 
> Client IP address: 172.16.1.43 
> Using Onboard Transceiver - Link Up. 
> SunOS Release 5.8 Version Generic_108528-06 64-bit
> Copyright 1983-2000 Sun Microsystems, Inc.  All rights reserved.
> Cannot load drivers for /pci@1f,0/ethernet@c
> Can't load the root filesystem
> Type  'go' to resume
> ok 
> 
> Any help would be greatly appreciated. I will summarize to the list.
> Thanks.
> 
> James Richardson
> Senior Unix Administrator
> Horry Telephone
> (843) 369-8549
>